After every household uses up tissues, there are inevitably many rolls of paper tubes left. Many people throw them away as waste, but they don’t know that it can also turn waste into treasure.
The purpose of rolling paper tube - How to make a rolling paper tube?
Purpose of roll paper tube
After every household uses tissues, there are inevitably many roll paper tubes left. Many people throw them away as waste, but they don’t know that it can also turn waste into treasure!
We can use rolled paper tubes to make some simple daily necessities, such as sock storage boxes, underwear storage boxes, jewelry storage boxes, wire storage boxes, pen holders, etc. Next, we will briefly introduce some methods to you:
1. There must be a lot of wires at home, such as TV cabinets, including TV cables, audio cables, DVD cables and VCD cables, which are intertwined and are easily exposed, causing safety hazards, and don’t know how to deal with them. Then you can now use a paper roll tube, find a place, use scissors to cut it from top to bottom, and then you can clip the wires from the opening (this case is suitable for the case where there are too many wires); if there are not many wires, you can do nothing to cut it open, just handle the wires and stuff them in. The principle here is to directly use its own bending degree to be used as a binding rope to store wires.
2. Use the paper rolling tube as a pen holder
to find four identical paper rolling tubes; take one of them, use a ruler to take a vertical line from top to bottom in any place, and use the back of the knife to scratch, do not cut, as long as there are scratches, the purpose of the scratch is to make a sharp corner more conveniently; fold out the sharp corners, and the four paper rolling tubes are treated the same; then use double-sided tape to paste the four paper rolling tubes, with sharp corners to sharp corners; now deal with the bottom, find a cardboard to paste it according to the situation;
Then repackage and paste the paper according to the twill marks of the paper rolling tube itself; if you want it to be more beautiful, you can handle the individual paper rolling tubes first before pasting, so that the effect is better.
There is four intervals in the pen holder, and different types of pens can be placed, which are easy to put and easy to find; another advantage is that in the gap between the two rolled paper tubes, you can also use small cards to record some commonly used information, such as business cards and post-it notes.
Board paper roll handmade
Waste paper roll can make many exquisite items by hand. Today, I will introduce you to the method of using paper roll to make vases and flowers.
Handmade simple vases for scrap paper rolls:
1. Preparation materials: several fresh mold paper tubes, wire, foam, knife, and paper.
Making method:
1. Cut the plastic wrap paper tube into three parts on average, and divide it into two parts shorter;
2. Then surround the cut plastic wrap paper tube into a rectangle (of course it can also be a square, you can choose according to your own preference), and then use a knife to penetrate two holes at the same height of each paper tube so that the wire can pass through it balancedly. Fix the rectangle and finally tie the knot, pay attention to tie the knot inside.
3. Cut the paper into a rectangle, then cut the top into a triangle, twist the bottom into a rope to make the feeling of green grass,
4. Put the grass in the paper tube. Then cut the foam to the same size as the bottom of the paper tube and put it in.
5. Put flowers on the foam and it’s done.
Waste paper roll tube handmade beautiful handmade flowers:
Materials and tools: two paper roll tubes (two paper roll tubes make a flower), hot melt glue gun, scissors, buttons, and a piece of paper.
If you want to install flower stems on flowers, you need the following: No. 28 wire, wire cutters (wire cutters), and paper bags.
If you want to color it, you need: pigment, brush.
1. Cut the first rolling paper tube along the center line; cut the rolling paper tube into four equal widths; cut two of the four strips 1/2 inch each; cut the second rolling paper tube along the center line and then cut in half; cut all rolling paper tube sheets into the shape in the last picture.
2. Make petals. A small amount of hot melt adhesive is placed at the middle point of a large piece of paper; stack the other large piece of paper horizontally and press down firmly; turn the remaining two small pieces of paper 90 degrees in the direction of the previous step; continue to stick the small piece of paper; stick the buttons in the center of the flower.
3. Make calyx. Measure, mark a piece of paper 3 inches away.
If you want them to bring some curls, wrap them around the pencil to shape.
4. Make flower stems. Find a wire, which is twice the length of the flower stem, peel it; fold the wire in half and twist it a few times; bend the end of the forked end to a 90-degree angle; cut a piece of paper tape from your paper bag; point a little hot melt glue at the end and wrap the paper tape around the wire; start from the bottom and wrap it up until the bend just now.
5. Stick the petals and leaves. Turn your flower over and glue a leaf; turn one end of the stem to the fork facing downwards, and bend it in the same direction as the cardboard sheet; apply some hot melt glue to the bent section of the stem and turn the other leaf 90 degrees to stick it on it; you need to hold it for a while until the hot melt glue cools down so that the stem will not overturn.
How to make a homemade paper rolling tube
The paper rolling tube should be used by most families. In fact, we might as well try to do it ourselves and use some discarded materials at home to make a well-made paper rolling tube, which is both cost-effective and environmentally friendly.
Materials required for homemade paper roll tubes: just use a waste paper box.
Required tools: one piece of tape rolls of size and width, wrapping paper, corrugated paper, photo adhesive (universal glue or double-sided glue).
1. First make the lid, use a paper roll with a smaller width as the lid, seal thick cardboard at the bottom, paste a circular decorative paper that is 1 cm larger than the round bottom, and cut the edge into strips;
2. Float the paper strip on the edge on the outside of the paper roll;
3. Cut a long strip of paper, equal to the circumference, and width is about 3 times the thickness of the paper roll, and then fold the upper edge into 1 cm, and use it to wrap the outside of the paper roll;
4. Cut the edge into a long strip in the same way, apply the photo glue (universal glue or double-sided adhesive) to the inside and the bottom edge;
5. Pull the edge strip to the bottom to float;
6. Cut out the circular decorative paper and paste it on the bottom, and the lid is completely packaged;
7. Let’s make the box body, use a wide paper roll to make the box body, first cover one side and cut an elongate paper, which is as long as the circumference of the paper roll, the width should be about 2 cm each on both sides, and the outer side of the wrapping paper roll;
8. Leave more 2 cm of paper on both sides and cut into long strips;
9. Float one end in the bottom;
10. Pull the other end into a strip to the inside to float;
11. Cut a circular decorative paper to the bottom to cover the white space;
12. Roll the long corrugated paper into a cylinder and place it in the box, the height must be about 1.5 cm more than the body of the box;
13. Finally, decorate the roll paper drum according to personal preferences to make the roll paper drum more beautiful;
14. Complete the homemade roll paper drum.